6x9s not working...not sure why..

[Baz]

build part of my boot install today...the bottom which sits in the boot nicely...and the sub box...put all the cable back to where they should be in the amp and the 6x9s don't seem to be working but not a clue why, help appreciated.

[Scott]

amp getting power? rcas connected? amp earthed properly? remote turn on working correctly?

[Baz]

amp works yeh as the sub is working....earth wire connected properly yes, remote lead workig fine too, whats the rcas?

cheers

[Scott]

is the sub working musically? the rcas are the signal wires, red and white plugs normally

[Baz]

o right yeh they are in fine. yeh the sub works with the beat as it should do so ive not a clue really, i think best bet is to disconnect everything then reconnect it all!

[KAMENi]

that's the best thing but takes most of your time.

check GAIN setting on the amp, and input selection

[Baz]

sorted 6x9s out now but lack of bass in sub now lol figure that out later

[Scott]

how many channels on the amp? and how are you connecting them to the amp with the sub

[Baz]

i have a 4 channel JBl GTO-75.4, i have wired it up exactly the same way it was before i took it off!

|+|-|+|-| <--- top row
|+|-|+|-| <--- bottom row

sub is on top row on the end two.
left 6x9 on the right side of bottom row and right 6x9 on left side of bottom row.

[reevesy_vtr]

has scott been round and broken them smileys/smiley17.gif

[Scott]

smileys/smiley4.gif

[Baz]

any ideas then? smileys/sad.gif ill take a pic of the actual amp and label what each lead is thats goin in and could you tell me whats in the wrong place....if anything smileys/smiley17.gif cheers

[Scott]

4 channel amp, have you two sets of rcas going into amp0 or one set with splitterS?

[Baz]

i have two lots of the red and white leads going into the amp.

[Baz]

right here are some pics of how everythin is wired up atm....and yeh it did work fine with that scuff on the amp.
wait a min while i do the links properly smileys/smiley7.gif

pic 1 (http://putfile.com/pic.php?pic=12/34711310487.jpg&s=x10)

pic 2 (http://putfile.com/pic.php?pic=12/34711321184.jpg&s=x10)

pic 3 (http://putfile.com/pic.php?pic=12/34711332162.jpg&s=x10)

pic 4 (http://putfile.com/pic.php?pic=12/34711345561.jpg&s=x10)

pic 5 (http://putfile.com/pic.php?pic=12/34711355526.jpg&s=x10)

[Scott]

take a trip into digital photography forum and learn about macro mode smileys/smiley17.gif

hmm wiring appears fine, have you adjusted the gain accidentally? have the frequency settings been adjusted?

does the headunit have fade control for outputs? may have faded it off?

other than that im stumped at the moment

[Baz]

take a trip into digital photography forum and learn about macro mode smileys/smiley17.gif
maybe later smileys/smiley17.gif none of the settings have changed to my knowledge unless my mate chnaged them when i was having my dinner....ill check that tomorrow, the level of the sub on the headunti it on 8 (max) usualy on 6 with volume on 20. So im not too sure at all whats wrong. if i find out what was wrong with it i'll let you know tomorrow....IF i find whats wrong.

Baz