View Full Version : do i keep the dual exhausts?
ahoward87
26th April 2010, 17:12
i have a dual 3" scorpion exhaust on my vts im not sure whether to sell it or not? not too keen on it anymore, i think i prefer the single exhaust pipe just on one side, what do you think, any suggestions good or bad please....
wingnuts
26th April 2010, 17:15
piccys lol
and you know you wanna sell it to me lol
ahoward87
26th April 2010, 17:21
piccys lol
and you know you wanna sell it to me lol
some how i thought you might pop up on this post lol. ill post pics up in a couple of hours.
wingnuts
26th April 2010, 17:23
to quote your brother
DAMN STRAIGHT!!! lol
---RoBsTeRz---
26th April 2010, 21:16
Im a fan i have twin exits, its a tad different :y:
wadoryu
26th April 2010, 21:26
need pics
J222JRA
26th April 2010, 21:28
IMO No...
ahoward87
28th April 2010, 13:25
pics are up in the progress section
brianS
28th April 2010, 13:28
if you sell it then will you need to buy a new exhaust and also a new back bumper?
wadoryu
28th April 2010, 13:29
i like them tbh
ahoward87
28th April 2010, 13:29
mmmmmm. in two minds now lol
Mike_08
28th April 2010, 13:30
Pics IMO
Edit: In this thread ;)
wadoryu
28th April 2010, 13:32
Pics IMO
Edit: In this thread ;)
they are right at the top of the progress thread section mate.
in this section would be easyier though
ahoward87
28th April 2010, 13:52
http://i806.photobucket.com/albums/yy341/ahoward_87/PICT0097.jpg
here you go
haz_pro
28th April 2010, 13:55
i think it looks good!
SaxoMuffin
28th April 2010, 14:10
Just get the one looks a whole load better :y:
hellonpluto
28th April 2010, 15:23
why have twin exhausts on a 1.6?
Caino
28th April 2010, 15:25
1 is nicer, but the dual doesnt look bad !
shaneio
28th April 2010, 17:43
keep them adz
ahoward87
28th April 2010, 21:43
yeh i might just do that, if i get loads of stick its coming off!!
Giraffe
28th April 2010, 21:45
hell no, mutton dressed as lamb I reckon, like things to stay at least in their original form, even if the exhaust is uprated, I don't think it does any favours cosmetically...
CHIP
28th April 2010, 21:45
Not the most offensive i've seen. They can look good imo, but need to sit straight and be a proper job!
sparky771
28th April 2010, 21:50
I think they can look good but then again tacky, i think they quite suit your sax though.
ahoward87
29th April 2010, 10:48
Not the most offensive i've seen. They can look good imo, but need to sit straight and be a proper job!
am having the brackets/hangers and rubbers replaced today so that they sit excately level with each other , just want them to poke in a inch more as i think they stick out too much but have no room for menouver
Tony
29th April 2010, 11:00
I think they're out of 'fashion' for Saxos but whether I'd bother changing it I don't know.
Actually I do, I probably would lol.
But then I'd probably want to get a new rear bumper due to the bit being cut out.
Jay_
29th April 2010, 11:46
they look OK, but i would get a single, BUT then as above you have the issue of the cut out bit in the bumper....
ahoward87
29th April 2010, 12:05
yes i will defo have to change the bumper if the exhaust goes.
tom130691
29th April 2010, 12:23
i hate them, but if you take them off you will loose your maccys street cred
ahoward87
29th April 2010, 12:30
i hate them, but if you take them off you will loose your maccys street cred
oh yes, forgot about that lol :clapping:
piranhamatt
29th April 2010, 18:39
Keep them, but move them further under the car so they don't poke out more than a cm or two
richy-90
29th April 2010, 19:14
i think that it looks really m8 keep it....defo :)
richy-90
29th April 2010, 19:15
goood lol sorrry
Nslade
29th April 2010, 19:16
I Like them tbh i really do!! :)
ahoward87
27th May 2010, 15:41
im not to keen on these so if someone wants to swap for a single pipe,
id be happy to swap them over for you too
Tom_Crx
27th May 2010, 15:49
I actually quite like duals, gives a nice symmetry about the car, but in the pic they need to be tucked in more under the car
vBulletin® v3.8.2, Copyright ©2000-2025, Jelsoft Enterprises Ltd.