Mobile Devices: Lite Theme CitroŽn: CitroŽn Trader | Saxo Trader | C2 Trader Peugeot: Peugeot Trader | 106 Trader Enthusiast: Saxperience


Go Back   Saxperience - Citroen Saxo Forum

Articles
Search Articles
Display Options
Showing articles 21 to 30 of 36
BobC 3rd July 2009 22:54
This sensor is of Hall effect type and is located on the gearbox output. It is supplied with +12 V. .. This sensor transmits information which, along with the engine speed, is used to determine the gear engaged. This information is used to: ē improve driving pleasure (engine hesitation),
BobC 3rd July 2009 21:23
The throttle potentiometer is located on the throttle housing. Supplied with +5 V by the ECU, this potentiometer transmits a variable voltage to the ECU which is a function of the position of the throttle (driver's wishes). This information is used for recognising no load and full load positions and transitories for acceleration,...
BobC 3rd July 2009 20:57
The main supply to the system is by means of a double relay, which provides 3 operating states: ē ignition off: − the power to some system components such as: . the injectors, . the ignition coil, . the fuel pump, . the canister bleed electrovalve, . the oxygen sensor heating resistors, . the air pump relay (specific to ifL5 depollution),...
BobC 3rd July 2009 18:25
The engine speed sensor consists of a magnetic core and a winding. It is positioned opposite a ring on the flywheel with 60 teeth, 2 of which have been removed in order to determine the TDC (top dead centre) position. When the teeth of the flywheel pass in front of the sensor, a variation in magnetic field is created. This variation...
BobC 3rd July 2009 17:52
The injectors are of twin jet type. They are supplied with +12 V via the double multifunction relay. The ECU controls the injectors separately by earthing them in the firing order 1-3-4-2 when the inlet valves are closed. The amount of fuel injected depends on the injector opening time (called the injection time). Pulses from the...
BobC 3rd July 2009 16:59
The ignition is of twin static type: BBC2.2 (Compact Coil Unit and no HT leads). The compact coil unit consists of 2 coils with 2 HT outputs. It is located directly above the spark plugs. Each coil consists of a primary winding linked to a secondary winding. Each secondary output is connected to a spark plug. This technology improves ignition...
BobC 3rd July 2009 15:42
Overview The piezo-electric type knock sensor / pinking sensor is mounted on the rear of the engine block. This sensor is used to detect knock (vibrations caused by the mixture detonating in the combustion chamber), often caused by pre-ignition. This phenomenon, if repeated, can destroy mechanical parts due to an abnormal rise in temperature...
BobC 3rd July 2009 14:57
Overview The inlet air pressure sensor is a new generation sensor and incorporates the inlet air temperature sensor. The inlet air pressure sensor constantly measures the pressure in the inlet manifold as well as the temperature of the engine inlet air. It is supplied with +5V by the ECU when the ignition is switched on. Inlet air...
BobC 3rd July 2009 11:57
Overview The idle regulation stepper motor is mounted on the end of the inlet manifold or on the throttle housing; it is controlled electrically by the ECU. This stepper motor controls an air flow taken in parallel to the throttle with the aim of: ē providing an additional air flow (cold starting), ē regulating an idle speed as a function of...
BobC 3rd July 2009 09:51
Overview The downstream oxygen sensor is used to comply with the EOBD regulations (European On Board Diagnosis) which applied to Saxos from 2001 onwards. It is located after the catalytic converter and it is used to check the efficiency of the catalytic converter. The specifications and heating device of the downstream oxygen sensor are the...
Top Authors

Article Forum v1.9 Copyright by BananaLive

All times are GMT. The time now is 17:33.