After many weeks of looking I have managed to get my hands on a 106 mk2 rallye blue carpet :) in very good condition for 35 pounds what a bargin :afro:

When I get time off work I will fit, and post pics so watch this space

i really , really want to give my vts some more.
most of the money i have spent to date has been on ICE and tarting it up, which both slow the car down by adding weight.

performance mods so far

- de cat
- stainless centre pipe
- mil tek stainless back box
- pipe cross filter
- re map

its what to do next tho. im thinging a 4 - 2 - 1 manifold. i had one on my vtr and noticed the difference. but the manifold which comes with a vts is a lot more flowing then he manifold on he vtr. so i don't think i will make a big difference...

first job you have to do is decide which colour will complment your car.

i decided yellow would look good with my wheels and; some cars like porchers come with yellow callipers lmfao.

my callipers on my old vtr i did to match the paint work of the car.

this was a lot of work, it ment priming, then paint lacker.

so i used hammerite, now i told my brother inlaw to do this on his celica a few months ago and they still look good.

and with it being hammerite no under coat needed, just clean them up with a wire brush. ...

iv been doing a lot of parts on my car with this carbon wrap.

i ran out and waited some more, so went on ebay as you do. and now they do the carbon effect in most colours. so iv got a roll of gold and blue; bit bored of the black lol. :D il keep you posted on what i end up wrapping

up date

tinted fogs
painted brake calipers yellow
carbon wrapped rear view mirror
painted areail
and gave her a good service :)

:afro:

[ATTACH]197[/ATTACH]

[ATTACH]198[/ATTACH]

[ATTACH]199[/ATTACH]

[ATTACH]200[/ATTACH]

[ATTACH]201[/ATTACH]

[ATTACH]202[/ATTACH]

[ATTACH]203[/ATTACH]

any other saxo owner will know about the body kit needs re bonding to the clips once they get to about 8 years old. well my vts had a new one today the areal fall off lol. the bolt stayed in the roof and the black plastic mount and the aireal fell off.

when i tuck a closer look the bolt was only bonded to a nirolen washer. so re attached it using epoxy resin.

but while it was off the car i decided to paint it posi blue to match the rest of my car. i think it looks bad assssssss. i admit flushing it off would look a lot better, but a least this way i can still get...

As I said in the post before i was going to use a spray tint, which i had left from an old project.

but i got bored yesterday, so had a big round in the shed for bits to sell on ebay.

and a found a roll of tint film, so decided to do them with the film.

the main reason i used the film is i couldnt be arsed to remove the fogs lights to spray them, to be honest.

so i gave the film a bash and i think they have come out well.

all i ded was;

1/ cleaned the fog light with hot soapy water
2/ cut a peice of...

As I said in the post before i was going to use a spray tint, which i had left from an old project.

but i got bored yesterday, so had a big round in the shed for bits to sell on ebay.

and a found a roll of tint film, so decided to do them with the film.

the main reason i used the film is i couldnt be arsed to remove the fogs lights to spray them, to be honest.

so i gave the film a bash and i think they have come out well.

all i ded was;

1/ cleaned the fog light with hot soapy water
2/ cut a peice of...

just seen a blue carpet out of a s2 l06 rallye for sale

i think would look rather swishhhhh in my sexo.

and i need to pull the carpet out to put wires in for my amp soo might as well fit a new one.

thinking of covering the roof liner in blue as well ,, but that wont be any time soon i think that will be a big job lol.

believe it or not blue isnt my fav color. red is ha ha, i just happened to buy a blue saxo and it went from there.

i did once own a diablo red lo6 which was a l.l and i sort of made it into a gti rep. well...

iv jut got a new rear bumper, which il put pic on when i have sprayed up

and got an engine start button which im going to make an mounting plate for and it in the bit in front of the gear stick, you know were you pennys norm go.

was going to make a plate to fill the hole and cover it in carbon wrap; then put the button in the center.

so they are the little jobs i am on with at the moo

also need to get my windows re tinted it anyone knows of anyone good in the grimsby area