Sorry to ask more questions mate, but are these the right ones;

http://www.maplin.co.uk/module.aspx?...&doy=24m3#spec

I dont have a Maplins near me, i tried typing in the code in the site but it wasnt having any of it

no u have to use SMD PLCC-2 LEDs in any colour u want (needed 16 of them for vts and 15 for vtr).


no mate there normal leds they dont list them on the maplins website u have to go in and ask for SMD PLCC-2 LEDs

here are some on ebay:

http://cgi.ebay.co.uk/10-SMD-SMT-PLC...QQcmdZViewItem

Legend. Cheers, Ill get 30 i think, then i know ive got enough for the rest of the dash if its possible. Already left you the rep matey

That does look mint m8.

Just wondering what is the far right dial on the vts?

AnDy

oil temp

they look wicked mate, just wondered when you driving at night can people outside the car see them, does it light up your face, if it doesnt then i might have to get some :y:

I doubt it Jim, theres still a dimmer switch on the underside of the dash you can use anyway to bring em right down

looks absolutly awesome matey

A what now??

Theres a roller switch, just by your right knee iirc, that changes the brightness of the dials. I definetely had one on the westy not sure if the furio has one or not thinking about it

Oooh, go check. I wonder if there is, lol.

Gutted, theres a slot for it, but theres no switch there. Maybe it was an option? You can see where it goes, just at the bottom right of the removeable panel underneath the wheel

Hmmm, may have to go check mine, never know mine could have the extra. Lol.

my switch there adjusts the headlights beam height not the dash brightness but i cant adjsut the dash brightness usign the two buttons on the clocks

How do you do that?

u have to push the buttons in a particular sequence i did it a few weeks back but cant remember the sequence off the top of my head

yeh that's the same as mine mate.


This is an awesome guide. Will borrow my grandads soldering iron and do this next week :P


scott

Awesome matey, I'll have to go have a fiddle now. Didn't know this my self. Cheers fella! :y:

try and get a needle tip soldering iron as it was a bit of a pain with the one i was using as it had a big head

might tell u in the hand book in the service pack what the squence is

ok yeh, I think he has a flat tip to his so I might need to smuggle one out of college to do it :)


Was the LED a direct replacement?


scott

yeah mate u have to get SMD PLCC-2 LEDs they are a direct replacement and look like this:



the end that has the corner notched is the positive side, make sure u put the new leds on in the correct way round. here are some on ebay: http://cgi.ebay.co.uk/10-SMD-SMT-PLC...QQcmdZViewItem

there were 10 sets on that ebay link earlier, its now down to 2 lol must have had a few poeple buy them off here

It says press the second dash button to change the brightness. I always wondered what that button did!!

to adjsut the brightsness u have to have the engine running and side lights on and then push the second button

hey up mate i have just been down to maplins and they say they dont do any lights like these with this code. is there any other codes?:panic:

what do u mean code? i never gave a code there SMD PLCC-2 LEDs but i dont have a code for them, they dont have them on the maplins website so not all stores might not stock them i jsut walked into my maplins and asked for some. u can get some on ebay if not

http://cgi.ebay.co.uk/10-SMD-SMT-PLC...QQcmdZViewItem

ok mate i went in and asked for smd plcc 2 and the bloke just looked at me wierd. maybe they dont do them in my store. i will have to buy off ebay instead:y:

only 2 left on ebay so u wana be qick

so you no all the littl clips on the back there must be at least 50 you dont need to unclip them lol???????

bet theres only about 10 or summit i was trying to unclip all the little ones and thought thats far too hard, are the clips just round the edge???

EDIT one set on abay now lol, im gonna do my mileometer :y: maybe even make the needles glow a different colour, they will probablies turn out purple lol

yeah u jsut need to do the clips around the outside and the 2 biggest ones in the middle of the circuit board

awsome mate

tempted to try this how bright are they

and can you see the milometer clearley from the pics it looks like you cant but may just be the angle of pics

great steve my smd leds are on there way :)

you can set the brightness mate using the 2 buttons on the clocks, read above as i put how to do it.

as for the millage display you can see it fine it looks like this:


but in this pics it looks bright but its like the above pic

nice steve, been wanting to do my digital bit for ages but could never find the right leds, ill rep you when i can mate :)

Anyone got another link where to purchase them.

Need more than 1 set of 10 as pred got the last nabs :p

muhahahaha ill probablies only need about 7 or 8 of them

2 for digital bit and 1 each fo the needles (might, might not) and a few warning lights

best thing to do is ask him if he has any more, also some white ones on there, they might be interesting :y:

Yea i did think white also.

Shall see lol, i'll ask him if he has more.

yeah ask him if he has any more, there are others on ebay but cost more
http://cgi.ebay.co.uk/10-x-BLUE-RED-...QQcmdZViewItem

cheers ste i did see the bit out of the dash and could see the milage when there you cant see it from pics so must be the angle

i know how to adjust them

I ment the code for the leds from maplins