Saxperience - Citroen Saxo Forum
Page 7 of 12 123456 7 89101112
Show 40 post(s) from this thread on one page

Saxperience - Citroen Saxo Forum (http://www.saxperience.com/forum/index.php)
-   Saxo Engine/Performance (http://www.saxperience.com/forum/forumdisplay.php?f=12)
-   -   Turbo setup, Can standard ecu be mapped for turbo?? (http://www.saxperience.com/forum/showthread.php?t=250882)

sliderz 2nd October 2009 11:06
arh thanks mr wide

jsdvtr 5th October 2009 13:23
Could i turbo on low boost with out need to fit decomp plate?

willtr 5th October 2009 17:02
Quote:
Originally Posted by tangoedvtsturbo (Post 3721324)
i have a vts turbo conversion done by the turbo doc!
rover turbo inlet
TD04 turbo
evo 9 intercooler
external wastegate n screamer pipe
14psi
8000rpm rev limit
megasquirt ecu
just pushed 200bhp at the fly after a kwik remap on the way down to L.A.D in morecambe!
is getting turned upto 18psi n mapped as soon as L.A.D have a free afternoon for me to use the dyno!
THE ENGINE HAD DONE 105000 MILES WHEN THE CONVERSION WAS DONE! NO FANCY PISTONS OR MODS! IT GOES LIKE FOOK N IT WORKS! NO SHINY BITS BUT AT THE END OF THE DAY ITS COST £800 U CANT BUY THIS TYPE OF POWER FOR THE MONEY ANYWERE ELSE!
what is the website or phone number for this guy so i can see if he can do mine for me.

stueyp 7th October 2009 12:47
Quote:
Originally Posted by willtr (Post 3732733)
what is the website or phone number for this guy so i can see if he can do mine for me.
His Name is chris and his number is 07790925333.

willtr 7th October 2009 16:05
Quote:
Originally Posted by stueyp (Post 3737801)
His Name is chris and his number is 07790925333.
thanks for the number mate

jsdvtr 7th October 2009 19:50
Where can i get a decomp plate from and how much will this be? I presume i will need a new cam belt with taking the head off?

stueyp 7th October 2009 21:06
Quote:
Originally Posted by jsdvtr (Post 3739196)
Where can i get a decomp plate from and how much will this be? I presume i will need a new cam belt with taking the head off?
Depends when yours was last changed. Tangoedvtsturbo has used two head gaskets on his.

jsdvtr 8th October 2009 11:32
Well the cars just turned 50k.

blackie_2k5 8th October 2009 12:10
Quote:
Originally Posted by stueyp (Post 3739502)
Depends when yours was last changed. Tangoedvtsturbo has used two head gaskets on his.
if your removing the head you always put a new cambelt on, bit of bad advice there mate, the belt will always be stretched when its been on the car, only time i wouldnt change it is if its only been on less then a week but ideally you should bre putting a new one on

stueyp 8th October 2009 12:40
Quote:
Originally Posted by blackie_2k5 (Post 3740951)
if your removing the head you always put a new cambelt on, bit of bad advice there mate, the belt will always be stretched when its been on the car, only time i wouldnt change it is if its only been on less then a week but ideally you should bre putting a new one on
Stretching cam belts????? That's a new one!!

jsdvtr 8th October 2009 13:16
Say if near the time i will be fitting the turbo kit can i get a new gasket, decomp plate and cambelt done which i will get done by a garage so its got it shown on service history and i wont be a ble to do it. Will it be ok to still run the car with the decomp on, etc even if turbo not yet fitted or should i get the turbo up and running then take to a garage to get all those done.

blackie_2k5 8th October 2009 13:18
Quote:
Originally Posted by stueyp (Post 3741064)
Stretching cam belts????? That's a new one!!
not at all mate but w/e

jsdvtr 8th October 2009 19:04
Found a decomp plate-
http://www.ferriday.co.uk/orders/dec...n_plates.shtml
Any good or is there better?

willtr 9th October 2009 15:45
http://cgi.ebay.co.uk/Citroen-Saxo-V...d=p3286.c0.m14

I have heard that these ones are ment to be good.

jsdvtr 9th October 2009 15:56
Quote:
Originally Posted by willtr (Post 3744336)
http://cgi.ebay.co.uk/Citroen-Saxo-V...d=p3286.c0.m14

I have heard that these ones are ment to be good.
Bargain.

willtr 9th October 2009 15:59
Quote:
Originally Posted by jsdvtr (Post 3744367)
Bargain.
Yeah i no i found this one ebay before and put up a thread about it and blackie_2k5 said he knew the guy that makes them and that they are good. I could link you to the thread page if you want so you can have a read?

blackie_2k5 9th October 2009 16:23
point to make is these need a slight bit of dressing where the bore holes have been prssed out, but in comparisin with dp engineering and ferriday etc are good value for money

willtr 9th October 2009 17:21
Quote:
Originally Posted by blackie_2k5 (Post 3744438)
point to make is these need a slight bit of dressing where the bore holes have been prssed out, but in comparisin with dp engineering and ferriday etc are good value for money

Thanks for that as i am thinking of getting this done at the end of the month to save me time and money. and how would i dress it?

blackie_2k5 9th October 2009 17:28
with a file or a die grinder, couple of little snots that need removing where the bore size wasnt totallt pressed out piece of piss

sexoturbs 10th October 2009 20:33
Quote:
Originally Posted by jsdvtr (Post 3741186)
Say if near the time i will be fitting the turbo kit can i get a new gasket, decomp plate and cambelt done which i will get done by a garage so its got it shown on service history and i wont be a ble to do it. Will it be ok to still run the car with the decomp on, etc even if turbo not yet fitted or should i get the turbo up and running then take to a garage to get all those done.
water pump, new head bolts. get it al done when you put the turbo on unless its not gong to be done fore a wile. i just done all mine :y:


All times are GMT. The time now is 08:46.
Page 7 of 12 123456 7 89101112
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.