does any body have a wiring diagram for a `99 vtr.
haynes manual should have it. i need the bit for the engine wiring and ecu. if somebody could scan it and e-mail it to me i would be chuffin...
thanx axhead

What is it you are looking for specifically???

Here's the full set.. for future reference peeps

bloody hell maybe needs to be made a sticky or put somewere were people can see

Thats why I edited the title, so people can search for 'wiring diagram'

ok big man never new that

nice one mate thats sound...

I do have a full ECU pin out somewhere, but I dont have my scanner setup... I grabbed the other diagrams from a PDF.

Let me know if you need anything else

where can i getta hold of a fuse box diagram, ive lost my haynes manual!

i need to change the fuse for my stereo from a 5a to 10a, thought u lot should know

sorry if ive posted in the wrong bit

your radio should already have a 10a fuse

i see...thanks

radio fuse 4, 10a

any chance in that ecu pin out mate...

hold on mate.
i have a pin diagram :afro:

ooohhh yippeee.. gimme gimme

give me some time. i need to type each pin out

o.k.. cant you copy and paste/,., or is it on paper/..

forum went down last night so here it ie.



23-air con
32-air con
34-air con
18-battery
22-coded key pad
35-coded keypad
11-crankshaft position sensor-
30-crankshaft position sensor-
19-crankshaft position sensor-
13-data link connector
16-data link connector
6-data link connector
2-earth
14-earth
19-earth
25-engine coolant temp sensor
26-engine coolant temp sensor
5-evaporative emission canister purge valve
10-heated oxygen sensor
28-heated oxygen sensor
19-heated oxygen sensor
15-idle air control
33-idle air control
1-ignition coil
20-ignition coil
3-inertia fuel shut off
17-injectors
26-intake air temp
27-intake air temp
22-malfunction indicator lamp
7-MAP sensor
12-MAP sensor
26-MAP sensor
37-relay module
3-relay module
6-tachometer
12-TPS
26-TPS
29-TPS
9-vehicle speed sensor

fuck me, thats a lot of copying

#30 Battery +
31 Battery -
В54 Crankshaft position (CKP) sensor
Х1 Data link connector (DLC)
А35 Engine control module (ECM)
В24 Engine coolant temperature (ЕСТ) sensor
H63 Engine malfunction indicator lamp (MIL)
Y104 Evaporative emission (EVAP) canister purge valve
М12 Fuel pump
F Fuse
В72 Heated oxygen sensor (HO2S)
Y99 Idle air control (IAC) valve
Т1 Ignition coil
15 Ignition switch - ignition ON
А162 Immobilizer control module
S39 Inertia fuel shut-off (IFS) switch
Y3 Injector
А5 Instrument panel
A75 Instrumentation control module
B25 Intake air temperature (IAT) sensor
В69 Knock sensor (KS)
B83 Manifold absolute pressure (MAP) sensor
A171 Relay module
P7 Tachometer
R10 Throttle body heater
В147 Throttle position (TP) sensor
B33 Vehicle speed sensor (VSS)
P9 Vehicle speedometer

Thats the diagram from autodata that I used to do the VTr to VTS conversion

bloody good info here!
stuck ;)

hurry up sean you only have a week now

lol i meant the thread has been stuck, not that i was stuck you fool ;)

pah il await our next convo on msn of help me it doesnt work

waiting a long time son ;)

Added to FAQ list

hi do you have the pinouts for the other side of the harness for a mk 1 and mk2 vtr as i have just put a replacement mk 2 engine in my 97 mk1. cheers

AX beefy, that diagram you posted on page 1 is that showing a vtr car loom plugged into a vts engine loom via that circular plug that its behind the passanger headlight in the engine bay?

would also like to know the same

anything to do with PAS on here or am i just blind, good diagrams but not quite what im looking for from what i can see as ive got a rogue wore in my power steering. ( the trigger for the relay (GREEN))

can you post the wiring diagram for the mk2 vtr or are they the same??

hi mate i see you have loads of wire in diagrams you dont happen to have picture and whatthe wires do on the multi plugs for a mk1 vtr engine loom and the multi plug pics for a 106 xn 5 dr cheers bud

Hello everyone, does anybody know where i could get the wiring diagrams for a 2001 vtr engine code "nft" cheers.

long time without writing....well im megasquirting mi 00' saxo vtr mk1 and these diagrams look fine but can anyone help me on this one....i will be using this harness from diyautotune:

as you can see this are labeled for every component....so my question is can anyone help me with the pin locations for this cables on the original harness connector? (for the bosch 1 big pin ECU)cause someone posted before but the pins were repeated sometimes so i got confused....thanks for your time bye!

this is what i mean with repeating pins ive sorted the pins by numer and i found several pins with 2 or more sensors attached to them and other ones with no use correct me if im wrong here is the list in order:
1-ignition coil
2-earth
3-inertia fuel shut off
4-not used
5-evaporative emission canister purge valve
6-tachometer (also data link connector?)
7-MAP sensor
8-not used
9-vehicle speed sensor
10-heated oxygen sensor
11-crankshaft position sensor
12-TPS (also MAP sensor?)
13-data link connector
14-earth
15-idle air control
16-data link connector
17-injectors
18-battery
19-crankshaft position sensor (also earth? and heated axygen sensor?)
20-ignition coil
21-not used
22-malfunction indicator lamp (also coded key lamp?)
23-air con
24-not used
25-engine coolant temp sensor
26-engine coolant temp sensor (also intake air temp? and TPS?)
27-intake air temp
28-heated oxygen sensor
29-TPS
30-crankshaft position sensor
31-not used
32-air con
33-idle air control
34-air con
35-coded keypad]
36-not used
37-relay module

hope it helps to someone

What specification Megasquirt did you buy?

hi i've buyed this one MegaSquirt-II EMS System - SMD PCB3.57 http://www.diyautotune.com/catalog/m...ase-p-171.html

anyone can help me on this one....bye!

so anyone here can help me please?? i need to install my megasquirt and i need to know the pins of the ecu...thanks a lot bye!

any chance of the diagram for a Saxo 1.4i or is it the same - i have fan problems

yes, good post..anyone try to pin diagram for the ecu magnetti marelli 48P2.80 3 plug saxo vts?
thanks

anyone know where i could get a pin out for the different multiplugs? i have a vts crossover loom (single plug ecu with big multiplug) and its in a y reg vtr, some pins dont match so i have no speedo, rev counter or temp guage and my battery and handbrake lights are permanently on!

thanks