saxo turbo oil drain to sump.
 

was suposed to do this ages ago but my car was to low. so wile its on the ramps here it is.
sump with oil feed just under sandwich plate.



custom home made oil drain pipe lol



pipe just sitting next to its fixings

as long as that is on an angle will be fine don't want it to straight otherwise oil will just pool there. But snap here is one of my old one pretty simple same cituning kit just I got it inseperates and got everythign else cheap

i think i will invest in a whole tube like that. instead of my spare bits and pipe lol.

nah if yours does the job mate then keep it at that just make sure there is more of an angle in it if poss as its gravity return

still need to get my sump sorted for this.

Think the sensor hole on the VTS sump is to far over, so may use that for an oil temp sensor and drill a hole to the far right (when you look from the front) of the sump.

just hoping i dont have to relocate my oil filter, cba with that lol

nope myn is getting on now lol. needs replacing! yea i no its easy for you. my mani sits my turbo right down next to it. but all is good :) thanks

lol my relocation was easy to do. but i bought it as a kit soo just had to put it together.

well mine is using an adapted standard mani, so im not sure how it will sit.

Will just have to find out, although i may just get a smaller filter, sure Gav said a R5 one fits and is half the size...

:O secrets that have been kept from me lol. well good luck man hope it fits!

was your downpipe always resting there or is it not fitted properly in that pic? looks to be touching the body

alos lads, should tag these pics into the turbo/supergharger thread will be a simple guide so to speak, evry little wil help for those who need the info :)

was just resting andy do you lot think it would be a benefit to post my old turbo build pics so people know what to expect?

id say defo mate, any pics can be good for ppl for reference, would probably save alot of random posts to, will give an idea of how things look, what sort of work is involved etc? evryone should post their pics and a lil explanation underneath of whats in the pic ie the oil drain to sump in the pics above :) all good for helping ppl out isnt it, that pic above will stop threads on where and how to fit an oil dran? so gotta be worth it imo

So that's what the Cituning oil drain looks like, when I was talking to them they said they used 2x hoses & a joiner :p

Sexoturbs, do you know the internal diameter of the hose?

Thanks.

yep this one is very old. off one of the 1st turbo kits they built. nope dont no the size but i havent yet filled my car back up with oil yet so could maybe take it bk off and measure it to nite. think ill be goin back to it about 6 to try get it started up.

Awesome, if you could get me the internal diameter it would be GREAT!! :y:

Thanks.

would that be so you could source some piping for your set up?

Pretty much, the basic kit from cituning is not supplied with any sort of gear to sort oil drain to the sump, I've seen on ebay a barbed flange for the turbo but the outlet size is only 16mm, I have nothing to compare this size against hence the favour from Sexoturbs :y:, from the reading I have done 16mm 'maybe' to small and I should be looking at 20mm :panic:

ManC

id say 16 would be resyrictive but then warm oil is quite runny, id imagine 20-22mm be better size

If you can get me the lengths and angles of each part i can get some sorted and im positive it would be cheaper than pt.

if you guys need a oil return pipe for your setups give me a shout when needed as the place I get my stuff from usually has off cuts and get them free so cost to you is postage depending on size needed

sorry people i fell asleep :O my bad! ill be round their 1st thing tomorow. so ill be sure to get the size for you