HOW TO remove black immobiliser box(non keypad models only)

[sam_16v]

a breif guide on how to remove the black immobiliser box on non keypad models so if you dont have the keypad this IS for you

ENGINE MUST BE RUNNING WHILST REMOVING BLACK BOX!!!!!!!!!!
IF THE ENGINE IS NOT RUNNING IT WILL LOCK YOUR ECU!!

1.locate the black box but dont remove it yet which is located in the passenger footwell behind the fuse box it will look like this:


2.start engine and leave to tick over
3.with the engine running remove the black box there is a plastic clip which i just prised it off with a small flat head screw driver and let engine carry on running for 5 mins
4.switch off engine then switch back on and job done

[Cam]

Good stuff sam !

[jeffchiz]

also just to add the there is a plastic clip which levers down to release the box, i was there for like half an hour tryign to figure out how to dissconnect it and in the end i just cut it off lol, it was only after i took it off i realised how to take it off properly

[sam_16v]

Originally Posted by jeffchiz

also just to add the there is a plastic clip which levers down to release the box, i was there for like half an hour tryign to figure out how to dissconnect it and in the end i just cut it off lol, it was only after i took it off i realised how to take it off properly

i just prised it off with a small flat head screw driver

[ryan_g86]

Originally Posted by jeffchiz

also just to add the there is a plastic clip which levers down to release the box, i was there for like half an hour tryign to figure out how to dissconnect it and in the end i just cut it off lol, it was only after i took it off i realised how to take it off properly

i did exactly the same thing, did take me a while to locate mine.

[williamsvts]

engine doesnt need to be running. ignition just needs to be on.

[yorkie]

What if ecu already locked??? And u cannot start car would this unlock ecu???

[saxojimmy]

my immobiliser light was flashing and car would not start and i ran a ignition feed to the feul pump from the stereing collum and it started then i took off my immobiliser and job done

[BaSSLjnE]

What are the benefits of doing this?

[Jay_T87]

So doing this removes the immobiliser completely? I.E. no need for little plastic fob key?

[sam_16v]

It just de activates the imobilizer so you can use another ecu. the fob only unlocks the doors so will still need it

[ryanmt]

Worth noting that you leave the box disconnected forever and if you are removing the engine to put in a donor car make sure the black box / keypad is removed BEFORE connecting the engine up.

This method works fine but soon as you connect up a transponder box or keypad it reverts back to its locked state!

[Jay_T87]

Originally Posted by sam_16v

It just de activates the imobilizer so you can use another ecu. the fob only unlocks the doors so will still need it

I didn't mean the central looking fob, I meant the Immobiliser fob that fits the little plug under the steering wheel

[tiptop]

The plug on that little black box, the wires coming from it are two of them grey or only one?

[chris1987]

Originally Posted by saxojimmy

my immobiliser light was flashing and car would not start and i ran a ignition feed to the feul pump from the stereing collum and it started then i took off my immobiliser and job done

hi m8 i have the same prob i put my engine in a new shell and now wont start yellow key light on dash flashing i started getting fed up with it now and i seen your feed and seems you had same prob how do i run the ignition feed could you plz explaine so i can try it on mine please many thanks chris

[SGregg]

If I remove the immobilizer box as above, I guess I can cut all the associated wiring out of the loom too?

[welshpug]

yup if you really wanted to.

[SGregg]

Originally Posted by welshpug

yup if you really wanted to.

I really want to

[scottie_436]

Same principle for keypad cars... Only you unplug the keypad with the engine running

[welshpug]

no need to have it running, just ignition on.