Mobile Devices: Lite Theme Citroën: Citroën Trader | Saxo Trader | C2 Trader Peugeot: Peugeot Trader | 106 Trader Enthusiast: Saxperience


Go Back   Saxperience - Citroen Saxo Forum > Citroen Saxo Related Forums > Saxo Engine/Performance
Register Member Photo AlbumsBlogs FAQ Calendar Experience

Saxo Engine/Performance If you're interested in tuning Saxo engines, or if you need to know something which is engine related... this is the place for you.

Reply
 
Thread Tools Display Modes
Old 5th April 2006, 16:06   #1
oilman
Established Member
 
oilman's Avatar
 
Join Date: Feb 2005
Location: Truro United Kingdom (England)
Posts: 1,229
iTrader Score: 1 (100%)
oilman has much to be proud ofoilman has much to be proud ofoilman has much to be proud ofoilman has much to be proud ofoilman has much to be proud ofoilman has much to be proud ofoilman has much to be proud ofoilman has much to be proud ofoilman has much to be proud ofoilman has much to be proud of
Default

A short lesson on Multigrades:

If you see an expression such as 10W-40, the oil is a multigrade.

This simply means that the oil falls into 2 viscosity grades, in this case 10W & 40.

This is made possible by the inclusion of a polymer, a component which slows down the rate of thinning as the oil warms up and slows down the rate of thickening as the oil cools down.

It was first developed some 50 years ago to avoid the routine of using a thinner oil in winter and a thicker oil in summer.

For a 10w-40 to attain the specification target a 10W ( W = winter) the oil must have a certain maximum viscosity at low temperature. The actual viscosity and the temperature vary with the viscosity grade but in all cases the lower the number, the thinner the oil, e.g. a 5W oil is thinner than a 10W oil at temperatures encountered in UK winter conditions.

This is important because a thinner oil will circulate faster on cold start, affording better engine protection.

For a 10w-40 to attain the other specification target a 40 oil must fall within certain limits at 100 degC. In this case the temperature target does not vary with the viscosity grade, if there is no "W", the measuring temperature is always 100degC. Again the lower the number the thinner the oil, a 30 oil is thinner than a 40 oil at 100 degC., which is typical of maximum bulk oil temperatures in an operating engine.

The engine makers are, of course, very well aware of this and specify oils according to engine design features, oil pump capacities, manufacturing tolerances, ambient temperature conditions etc. It is important to follow these guidelines, they are important and are an are stipulated for good reasons.

If the engine has been modified, the operating conditions may well be outside the original design envelope. The stress on the oil caused by increased maximum revs, power output and temperature may indicate that oil of a different type and viscosity grade would be beneficial.

Cheers
Simon
__________________
Use the code SAXP and get 10% Club Discount
email: sales@opieoils.co.uk
phone: 01209 202944
oilman is offline   Reply With Quote
Old 3rd May 2012, 22:20   #2
Furio-Gazza
Saxperience Post Whore
Track / Motorsport PrepWest Midlands Region MemberEast Midlands Region MemberNorth West Region Member
 
Furio-Gazza's Avatar
 
Join Date: May 2010
Posts: 6,234
iTrader Score: 16 (100%)
Furio-Gazza is on a distinguished road
Default

That was actually a decent read & i learnt a few things there...Top Stuff
Furio-Gazza is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 03:49.