Engine Building

[D4MJT]

Talk to me.

I have an engine, it's healthy enough, and works. I've never had it on a roller but it's essentially a standard TU5J4. Goes nicely.

It's on 106k miles currently. I have full history for it, and at 90K it had a top end rebuild consisting of some valves as the belt snapped.

It's currently on an engine stand in my garage as the cam ladders are leaking oil etc.

I'm sorely tempted to rip it all apart and rebuilt it, quite simply, because I've never built an engine. Talk to me. What are good books to read, basic tools required etc?

It's for my 106, I don't "NEED" it on the road, I have a daily, so I can take my time. There's nothing wrong with the engine per se, but going forwards the car is likely to be only used in anger on a track or occasionally for a weekend run out, so I'd intended on baffling the sump etc anyway.

The idea of doing an all out build appeals as I'll get enjoyment out of building it, learning how to do it, and it's a known good starting place.

Thoughts / advice?

[Brettles1986]

Don't bother. You will get stuck, call Muz and then fuck it up twice as bad.

[D4MJT]

Don't bother. You will get stuck, call Muz and then fuck it up twice as bad.

Muz is now a redundant partner in Team Fastrape, last week I discovered I can make tea myself!

[Ali123]

I'm sure the Haynes manual has all the information needed I would of thought, and majority of shite needed is all te basic stuff, spanners and sockets, will need those E sockets for sockets for the head bolts like and a piston ring compressor to make life abit easier getting the pistons back in, assuming you're wanting to put new rings in etc ?

[Brettles1986]

Muz is now a redundant partner in Team Fastrape, last week I discovered I can make tea myself!

It's only a matter of time before you realise tea making time could be used for cable tying things together instead and he gets reinstated.

[D4MJT]

I'm sure the Haynes manual has all the information needed I would of thought, and majority of shite needed is all te basic stuff, spanners and sockets, will need those E sockets for sockets for the head bolts like and a piston ring compressor to make life abit easier getting the pistons back in, assuming you're wanting to put new rings in etc ?

Yeah I will be, I was thinking more along the lines of measuriser giblets for tolerances, and crank checking, and that sort of jazz?

As you can tell I have no idea what I'm talking about, as usual.

I've got sockets and all that sort of shit, I'm basically a professional.

[chompy]

I've done a few.

You'll need:
Various T size sockets (female & Male )
Big bar
impact gun (makes life easier)
Various sockets & spanners

I'd start with the bottom end if I was you. Strip the sump off and get the crank out then go from there.

Also, Haynes wins. As does autodata.

[Gandi699]

piston ring compressor would be useful too as would an angle gauge for torquing and maybe a dial gauge if you wish to measure some bits and bobs.

[chompy]

piston ring compressor would be useful too as would an angle gauge for torquing and maybe a dial gauge if you wish to measure some bits and bobs.

Nobody mentioned rebuilding it :homme: :clapping:

[Gandi699]

angle grinder it is then!

[holdawayt]

One of the most therapeutic and enjoyable things I've ever done weirdly.
Just being able to sit in a warm garage with some music on with a beer and methodically work your way through it all.

You'll learn shit loads too, go for it.

[D4MJT]

One of the most therapeutic and enjoyable things I've ever done weirdly.
Just being able to sit in a warm garage with some music on with a beer and methodically work your way through it all.

You'll learn shit loads too, go for it.

I like this, this is basically what I'm thinking.

I have a desire to do it and know what it's all about, so I think it'll need done really. :y:

[chompy]

I like this, this is basically what I'm thinking.

I have a desire to do it and know what it's all about, so I think it'll need done really. :y:

Awaiting the "Where does this go" posts

[johnnyg_vts]

'Why have I got all these bits left over?'

[Ali123]

'Why have I got all these bits left over?'

Just spares mate

[Mickswan]

Valve spring compressor

[Brettles1986]

Awaiting the "Where does this go" posts

awaits picture of penis with the above statement.

[Duffy Xsi]

I think it's a good idea. Good way to learn and if it does fuck up. It's not expensive engine to replace. Also if ure planning on tracking it it's a good time to upgrade stuff.


Sent from my iPhone using Tapatalk

[stevo67]

A good torque wrench,a compressor with an air line is also good but not essential.

[MuZiZZle]

Muz is now a redundant partner in Team Fastrape, last week I discovered I can make tea myself!

Don't tell me you've also found a local homeless person to call you a bender :(

I put the "Rape" in Fastrape