icv guide on blacktops (early mk1's)

[666]

theres no guide on idal control valve location on blacktops so heres a guide on were to find it
the other guides are for silver tops and are totaly diffrent

the icv is located
on the drivers side of the engine below the first inlet port the/injector/sparkplug

you wont be able to see much of the sensor but the 3 wire plug is visible
also you can follow the vacume pipe that goes from the trottle bodie to the icv

in the first pic the arrow going don points to the icv location, the top arrow shows the vacum pipe that leads to it



close up pic shows the icv (circled) and i have drawn a arrow to the same vacum hose to help show were the pic was tacken from



going closer but pics from side of bay heres the sensor(circled)



this is the closest i can get a pic, the icv is held in place with a large rubber band, undoing the vacum hose from the tb will help get it out
(wont move if the hose is connected) just unplug the sensor and hose and pull the icv towards the passenger side(you will have to do somme of this by touch as you cant see it propley), then you will be able to follow the last hose back to airbox(mine goes to my raceland) and disconect it



you dont need to remove anything other than your induction kit/airbox(to get your arm around the inlet manyfold)

make sure that when you remove and refit you havent knocked any vacum pipes lose(theres a small pipe with a t join infront of the inlet manyfold that came of easy on mine) or it will run like shit

hope this helps a few people out as its asked a lot

will be linked to my other guides in the stickys

[Mochachino]

il link it to my ICV guide too mate.

For all other engines that aint black tops, there is this guide or you.

http://www.saxperience.com/forum/sho...d.php?t=174710

[666]

nice one mate

[turbomadvtr]

Thanks for this m8.
By the way how dont you get oil spraying out of your mini breather filter as when i set mine up like this - it pished out !?!

[666]

no prob mate,
do you have the baffel inside the rocker cover, its a long steel plate it stops the oil hittting the breather

[turbomadvtr]

Originally Posted by 666

no prob mate,
do you have the baffel inside the rocker cover, its a long steel plate it stops the oil hittting the breather

Yeah m8 i do , it was fine for a few miles then when i next checked it was all over my engine and the mini breather was soaked with oil , where as yours is clean as a whistle.
Is it possible ive fitted the baffle plate the wrong way up when ive changed the rocker gasket ?!?!

[666]

Originally Posted by turbomadvtr

Yeah m8 i do , it was fine for a few miles then when i next checked it was all over my engine and the mini breather was soaked with oil , where as yours is clean as a whistle.
Is it possible ive fitted the baffle plate the wrong way up when ive changed the rocker gasket ?!?!

its been fine for about 3000miles so far, you could try reitting the baffle, if that dosnt work try changeing the oil filter, the oil filter is what controls oil pressuer, and yours mite be alowing to much oil presuer, oil shouldnt come up the pipe/breather or it will go in to the tb

[turbomadvtr]

Originally Posted by 666

its been fine for about 3000miles so far, you could try reitting the baffle, if that dosnt work try changeing the oil filter, the oil filter is what controls oil pressuer, and yours mite be alowing to much oil presuer, oil shouldnt come up the pipe/breather or it will go in to the tb

I bought a oil catch tank because of it spilling all over and it still ended up spilling out of the can through the filter lol. I have no luck.
But the pipe was bent over from the rocker, so can a bent pipe from rocker to catch tank cause too much pressure to make it flow out of the catch tank breather filter !?

[666]

i wouldnt of fort so mate, i ran mine for a week with no pipe or filter untill the breather arrived and only vapor should come out if oils getting out the top something isnt right thats what made me thing to much presser

[turbomadvtr]

Originally Posted by 666

i wouldnt of fort so mate, i ran mine for a week with no pipe or filter untill the breather arrived and only vapor should come out if oils getting out the top something isnt right thats what made me thing to much presser

OMG im such a nub

I put my baffle plate in wrong lol

[666]

lmao, glad you sorted it out mate, suprised it made that much diffrence tbh

[ianyerman]

can here a sound of air sucking in around this location on my blacktop.
can not find where it is sucking, i know there is a leak somewhere as the idle isnt good. has anyone else had this problem?

[That-Guy]

Originally Posted by ianyerman

can here a sound of air sucking in around this location on my blacktop.
can not find where it is sucking, i know there is a leak somewhere as the idle isnt good. has anyone else had this problem?

I have this with my Pug XSI, which I think is pretty much the same engine, but cant seem to find the leak. Mine idles a little lumpy

[666]

it will be a vacum leak, theres so many pipes and it only takes a very small split, only way is to remove each pipe and check very closed for probs

[That-Guy]

Originally Posted by 666

it will be a vacum leak, theres so many pipes and it only takes a very small split, only way is to remove each pipe and check very closed for probs

Oh god

Let the fun begin....

[Lloydie]

Get this sticky'd

[saxodunc]

thanks for the useful thread.
any 1 still got the pics to go with it?

Cheers

[Grant22]

the pictures aren't coming up. this guide is really useful but can u put the pictures up again it would really help me out cheers.

[Grant22]

the pictures aren't coming up , this guide is really useful, but could you put the pictures up again it would really help me out. cheers.

[darael]

Does anybody have the pictures from the first post?