engine loom (wiring diagram)

[hesslevtr]

Originally Posted by Sean

bloody good info here!
stuck

hurry up sean you only have a week now

[Sean]

lol i meant the thread has been stuck, not that i was stuck you fool

[hesslevtr]

Originally Posted by Sean

lol i meant the thread has been stuck, not that i was stuck you fool

pah il await our next convo on msn of help me it doesnt work

[Sean]

waiting a long time son

[Scottp]

Added to FAQ list

[mrsga69]

hi do you have the pinouts for the other side of the harness for a mk 1 and mk2 vtr as i have just put a replacement mk 2 engine in my 97 mk1. cheers

[fredjudd]

AX beefy, that diagram you posted on page 1 is that showing a vtr car loom plugged into a vts engine loom via that circular plug that its behind the passanger headlight in the engine bay?

[l1ukeRS]

would also like to know the same

[jonezy]

anything to do with PAS on here or am i just blind, good diagrams but not quite what im looking for from what i can see as ive got a rogue wore in my power steering. ( the trigger for the relay (GREEN))

[Rhea21]

can you post the wiring diagram for the mk2 vtr or are they the same??

[jonny106xn]

hi mate i see you have loads of wire in diagrams you dont happen to have picture and whatthe wires do on the multi plugs for a mk1 vtr engine loom and the multi plug pics for a 106 xn 5 dr cheers bud

[wannaberocker]

Hello everyone, does anybody know where i could get the wiring diagrams for a 2001 vtr engine code "nft" cheers.

[saxosuper1600]

long time without writing....well im megasquirting mi 00' saxo vtr mk1 and these diagrams look fine but can anyone help me on this one....i will be using this harness from diyautotune:

as you can see this are labeled for every component....so my question is can anyone help me with the pin locations for this cables on the original harness connector? (for the bosch 1 big pin ECU)cause someone posted before but the pins were repeated sometimes so i got confused....thanks for your time bye!

[saxosuper1600]

this is what i mean with repeating pins ive sorted the pins by numer and i found several pins with 2 or more sensors attached to them and other ones with no use correct me if im wrong here is the list in order:
1-ignition coil
2-earth
3-inertia fuel shut off
4-not used
5-evaporative emission canister purge valve
6-tachometer (also data link connector?)
7-MAP sensor
8-not used
9-vehicle speed sensor
10-heated oxygen sensor
11-crankshaft position sensor
12-TPS (also MAP sensor?)
13-data link connector
14-earth
15-idle air control
16-data link connector
17-injectors
18-battery
19-crankshaft position sensor (also earth? and heated axygen sensor?)
20-ignition coil
21-not used
22-malfunction indicator lamp (also coded key lamp?)
23-air con
24-not used
25-engine coolant temp sensor
26-engine coolant temp sensor (also intake air temp? and TPS?)
27-intake air temp
28-heated oxygen sensor
29-TPS
30-crankshaft position sensor
31-not used
32-air con
33-idle air control
34-air con
35-coded keypad]
36-not used
37-relay module

hope it helps to someone

[luthor1]

What specification Megasquirt did you buy?

[saxosuper1600]

hi i've buyed this one MegaSquirt-II EMS System - SMD PCB3.57 http://www.diyautotune.com/catalog/m...ase-p-171.html

anyone can help me on this one....bye!

[saxosuper1600]

so anyone here can help me please?? i need to install my megasquirt and i need to know the pins of the ecu...thanks a lot bye!

[honestman]

any chance of the diagram for a Saxo 1.4i or is it the same - i have fan problems

[rickycupportugal]

yes, good post..anyone try to pin diagram for the ecu magnetti marelli 48P2.80 3 plug saxo vts?
thanks

[LeeM]

anyone know where i could get a pin out for the different multiplugs? i have a vts crossover loom (single plug ecu with big multiplug) and its in a y reg vtr, some pins dont match so i have no speedo, rev counter or temp guage and my battery and handbrake lights are permanently on!

thanks