*webby's progress thread FOR SALE*

[webby]

Originally Posted by Lippy

how did you do the cables through the front doors? im doing this myself at the moment but failing to find the channel behind the spare plug slots that I drilled out... couldnt really see properly as was night time.
Did you use the standard plug or pummel holes in the car door and shell? piccys would be great!
Cheers

i used the standard plug. i wasnt messing about i just took the door off it made it lots easier. the plug is made of 2 parts and both need drilling iirc i dont have any pics im afraid. there was alot of swearing but in the end it happend.

[webby]

well they car hasn't changed from the last update but i have been gathering parts.

this is how it stands at the minute.





i have been out and bought:

-LEDA gas single adjustable rear dampers.
-LEDA gas single adjustable remote reservoir front coilover struts.
-Compbrake solid adjustable top mounts.
-Uprated organic valeo clutch (friction and pressure plate).
-Lightweight alloy crank pulley.
-Fog lamp covers.
-Bucket seats.
-A set of alloy wheels not saying what but they are the SEX. light too

my future purchases/plans will include.

-2.5"x8"x175lb faulkner springs
-4-point harnesses prefferably 3" fia approved ones
-Stud conversion.
-Full repaint in the same colour
-Full engine rebuild inc mains & big end bearings and rings
-Port matched & flowed head
-Custom intake plenum and induction kit.
-Custom lower strut brace.
-Upper strut brace.

i will upload some pics of the new bits tomorrow in the daylight.

[wickedrob]

very clean looking wicked red saxo,

[johnnyg_vts]

Originally Posted by webby

here is a picture of my current induction set-up. can tell no difference between that and the piper-x i had fitted. it is very quite so i am moving on to yet another one hopefully before fcs.

where did you get that pipe from?
i fancy a pikey addition to my air filter too.

[webby]

Originally Posted by johnnyg_vts

where did you get that pipe from?
i fancy a pikey addition to my air filter too.

yeah that does look pretty pikey lol.


i got it from the garden shed it was just lying about in there, im sure you can get it from any motorshop.

its changed since then to a bmc set-up.

[3cott]

Good progress webby

[webby]

Originally Posted by wickedrob

very clean looking wicked red saxo,

Originally Posted by 3cott

Good progress webby

cheers lads.

its coming along well im not half harting this anymore hence the suspension. any bits will either be top notch proven gear or custom made & designed.

[Sophia_Bush]

bastard LEDAs!! awesome!

[webby]

Originally Posted by Sophia_Bush

bastard LEDAs!! awesome!

yeah especially at the price i got them at, retail puts them at 2k excluding the top mounts. i paid a damn sight less.

as said here are a few pics.

front strut


rear damper


top mounts


clutch


lightweight crank pulley


seats


im going to be making some custom sub frames for the seats to mount them low enough so i can get in with a helmet on.

the LEDAs have just been serviced too so are in perfect working order. they are going to get a lick of paint before they are fitted.

[lukedavies1989]

gorgeous colour not to keen on the seats tho soz!

[webby]

they are not my favs' but i still like them they are there to serve a purpose though do a better job of holding me in than standards.

and tbh function is following form now but im not forgetting it.

[Phsyco_Paff]

very very nice

[Olly]

Where did you source the leda's? Was someone selling them that didnt know what they were?

Nice dude! Keep it up

[webby]

Originally Posted by sax-oli

Where did you source the leda's? Was someone selling them that didnt know what they were?

Nice dude! Keep it up

nah the guy i got them off had just upgraded to ohlins stuff during the off season so just wanted rid. he had them fitted with 325lb front springs and 23mm rear bars, he wanted to keep them bits though.

i have had a change of plan too and tbh its your car that has given me the kick up the arse to do it properly.

so this is going to remain as is with a few little tweaks nothing major and im selling my civic and buy a vts to compete with.

[webby]

well t-minus 6 days before its off the road and i cant wait.

im sick of the bastard tbh!
its has become nearly undrivable with a clutch right on its last legs and a icv playing up coupled to a few other bits. im fairly sure the head gasket has started leaking too.

im taking it up to wayne to get it thrown on the rollers just for a figure before its winter going over and then i'll go after winter for comparision.

keep an eye out for a spec list which should be getting typed up later but a few things will be changing.

[raunchz]

sounds like you'll need to go stiffer to match the leda dampers? maybe 250lb+?

[webby]

Originally Posted by raunchz

sounds like you'll need to go stiffer to match the leda dampers? maybe 250lb+?

good thing about these ross they are adjustable gas struts so i can pretty much run anything from 150lb to full blown tarmac race 400lb+.

im still undecided on what rate tbh. because i cant afford torsion bars atm.
so might stay on the softer side because springs are only £50 a pair. 2.5" i.d springs are pretty common.

[raunchz]

Originally Posted by webby

good thing about these ross they are adjustable gas struts so i can pretty much run anything from 150lb to full blown tarmac race 400lb+.

im still undecided on what rate tbh. because i can afford torsion bars atm.
so might stay on the softer side because springs are only £50 a pair. 2.5" i.d springs are pretty common.

Sounds a great set of dampers!! 2.5" springs are cheap from rallyedesign and DT and Faulkner so is a good plan !! Will be cool to hear how these handle !!

[saxo_ron]

Good work webby!!

[webby]

well as said this is all the crap that should be happening over winter.

Saxo vts

Engine.

Rebuilt with new rings and bearings gaskets.
new icv.
Lightened and balanced internals inc flywheel.
Alloy crank pully
Port matched and gas flowed head.
4-2-1 manifold.
race- cat.
2“ exhaust 2.5" outlet.
Timing belt and tensioner. (Water pump)
Newman ph3 Cams
lower engine mount
ported & polished throttle body
current induction with fabricated cold air scoop.
I may modify a spare slam panel to aid a bit more air flow.

Transmission.

Clutch.
Group n gear linkages.
New selector pins.

Suspension.

Leda suspension .
New top mount bearings.
8”x2.5”x175lb Faulkner springs.
upper strut brace.
Custom made lower strut brace.
Rebuilt rear beam.
Stud conversion
5mm spacers

Brakes.

rebuilt 247mm
1144’s
Castrol srf racing fluid
standard discs
Exact braided lines.


Exterior.

Wind deflectors.
Fog lamp covers.
Full respray wicked red
De-aerial
De locked boot trim
smoothed badges
Mk1 spoiler
Remove washer jets front and rear
De-locked
Desire grill
Saxo side badges
Remove 16v
Painted standard headlight inserts
Smoked side repeaters.


Wheels & tyres.

6x15" alloys. Im still not telling.
Toyo t1r’s

Interior:
momo steering wheel.
Snap-off boss
Bucket seats
Retrimmed in black leather/dark grey alcantara

Ice:
pioneer deh 80 mp
oz audio components
genisis sm100 ( amazing sq) for comps
jbl gt4
jbl 75.2 for sub
custom boot install
deadened roof doors and boot

im looking for a nice quick road car which i think that little lot should produce.
it wont see much track action maybe donny next year before they wreck it for f1 and the ring in summer.